OEM/ODM Factory for ASTM F912 F912M Alloy Steel Socket Set Screws for Maldives Manufacturer

Use this knowledge only for good, not evil!
The CIA Lockpicking Manual: https://amzn.to/1NqJe82
Visual Guide to Lock Picking (Third Edition) Perfect Paperback: https://amzn.to/1P1p6K1
9-Piece Unlocking Lock Pick Set Key Extractor Tool: https://amzn.to/1R1DQWL
Leather Packing Titanize Scissors And Single Hook: https://amzn.to/1Pk8Pij
Mything(TM)Professional Cutaway Practice Crystal Padlock+Lock: https://amzn.to/1jeKU7W

Watch more Home Security & Safety videos:

Locked yourself out of the house? Most common pin and tumbler locks can be picked with a little luck and finesse—so before you call a locksmith, try this.

Warning
Only pick your own locks—or you could wind up in a lot of trouble.

Step 1: Get a paperclip
Get a paperclip or safety pin and bend it straight. Now make a slight upwards bend at the very end.

Tip
You can buy a professional lock pick set at a hardware store. There is a basic size intended for American locks.

Step 2: Insert the wrench
Insert your wrench into the lower part of the keyhole—that is, the side opposite the one where the key’s teeth would go in.

Step 3: Determine direction
Figure out which way the lock needs to be turned to open by turning the wrench clockwise and then counterclockwise. You’ll feel which way has more give.

Step 4: Turn the lock
Turn the lock the correct way with the wrench, putting slight pressure on it. Hold the wrench in place.

Step 5: Insert the paperclip
While keeping pressure on the lock, insert the end of the paperclip into the top part of the keyhole.

Step 6: Feel for pins
Feel around the keyhole with the paperclip until you locate the pins. If you’re picking a common door lock, there will most likely be at least five of them in a row.

Tip
Before you start, many experts suggest ‘raking’ the lock. Straighten your second paperclip, put a few bends at the wire’s end, and—with no pressure on your wrench—shove it to the back of the lock. Now pull it out quickly, pressing against the top of the lock while gently turning your wrench. You might just set a pin or two that way.

Step 7: Push up
Now for the actual ‘picking.’ One at a time, push each pin up with the paperclip. Try to feel for the moment when the pin reaches its ‘unlocked’ position. You should feel a slight give—or even hear a faint click.

Tip
Start with the pin furthest away from you—then move on to the next.

Step 8: Increase the pressure
As you go, apply slightly more pressure with the wrench until you have all the pins lifted up.

Step 9: Turn the wrench
Now turn the wrench fully. Voila! The lock will pop open.

Did You Know?
Wooden locks were used as far back as 4,000 years ago in ancient Egypt.

I am presenting how to replace, install shower or bathtub rough in Valve ! STEP BY STEP! How to solder copper pipes, preparation and installation of cartridge. How to clean, cut and connect copper plumbing pipes. I am using Delta valve.
_____Click link to donate and support my Channel , thank you.____ https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=Y5L8X4XRSAXXN

For KOHLER, MOEN or HANS GROHE fixtures installation will be very similar !!
.https://www.tilemasterga.com
Most of the times reason to replace old fixture is leak , or simply bathroom remodeling.
I hope my video will help you at some point with your shower valve project.
Check my YouTube channel – you will find plenty other great videos:
- how to install shower pan and mud base
- how to tile walk-in shower step by step
- how to remove and install new bathtub
- soldering copper and brass pipes
- custom shower systems installation
- shower seat installation
- waterproofing bathroom with membrane
- tiling tub surround walls

and way more !!!!

Enjoy and do not forget to subscribe if you like my VIDEOS !

Thank you for stopping by !

Michael – Tile master Atlanta GA