Trending Products DIN 74361-H Flat Collar Nuts Wheel Nuts with Washers Wholesale to Austria

https://honda-tech.com/how-tos is the leading Honda Accord and Civic resource for technical DIY guides. The brakes are arguably the most important components of any vehicle. For the step-by-step article, please visit https://www.honda-tech.com/how-tos/a/honda-accord-how-to-replace-brake-pads-calipers-and-rotors-374563

This moderately difficult job takes 4-5 hours and costs $600+. A professional may charge from $1,500+.

This job requires a ratchet and socket set, hub-puller, torque wrench, breaker bar, C-clamp, hydraulic floor jack and jack stands, an off-set 12 millimeter wrench, and an assistant.

If you need to replace the calipers, you will need to drain or siphon the brake fluid from the master cylinder and bleed the brake lines before jacking up the car.

Step 1 – Jack up car

Loosen the lug nuts. Jack the front end up. Set car on the jack stands and remove wheels.

Step 2 – Remove spindle nut and bolt

Use a screwdriver or a nail and hammer the spindle bolt in the void where the metal bends in to make it form a circle so you can pull it off.

Use a 36 mm socket and long handled ratchet to remove the bolt. An air ratchet is optimal.

Have someone depress the brake pedal while you wrench on the bolt and complete Step 3.

Step 3 – Loosen four flange bolts on hub

Break free the four flange bolts on the front of the hub.

Step 4 – Remove two caliper housing bolts and caliper

Use a deep-well socket to work around the brake lines. Remove the bolts, and the caliper will come right off.

Set the caliper aside if it is still good and doesn’t need replacing. Otherwise, you’ll install the new caliper after the rotors are replaced.

If you are going to replace the calipers, you’ll need to bleed the lines at this point. You can use the small vice grips to minimize the amount of fluid to bleed. Use a C-clamp or large channel locks to compress the caliper pistons and force the fluid out the bleeder valve into your container.

In order to replace the caliper, disconnect the brake line by removing the banjo bolt.

Step 5 – Pull caliper bracket

Two bolts hold the caliper bracket in place. When you are removing them, loosen them both first; then, remove the bottom bolt before removing the top bolt, and the entire bracket will pull right off.

Step 6- Remove four rear hub bolts

There are four 12 mm bolts on the rear of the hub that need to be removed. Use an offset wrench. You will have to push the drive shaft protector away to get the wrench in there, and you may need to use some WD-40 or other spray lubricant to help get those bolts loose.

Step 7 – Remove hub

Place the hub-puller over two lug nut screws and screw those two lug nuts back on.
Put the hub puller cross-member on and screw that center bolt down until the hub and wheel bearing pop off.

Step 8 – Grease the wheel bearing and axle end

With the hub pulled, now is the perfect time to give the wheel bearings and axle ends a little TLC. If they are rusty, get some 800-grit sandpaper and get rid of as much rust as possible. Once that is cleaned up, use some multi-purpose grease and lube the wheel bearing, axle, and housing.
Replace the four rear hub bolts.

Step 9 – Put the new rotor onto the hub

Make sure that you are putting the rotor back onto the hub in the correct direction.

Step 10 – Re-install the rotor and hub unit onto the bearing and axle end

Line up the four bolts from the rear of the hub unit with the hub assembly so you can get a bite on those bolts. You will have to play with the bearing to get it in and get those bolts to bite.
Once those bolts get a good bite and are in well, use a rubber mallet and hit the assembly in place until it is in there well. Tighten those four back bolts and use the mallet to hit it some more.

Step 11 – Assemble the new pads and calipers

The hardest part is over. Now it’s time to reassemble everything. Put your new pads into the new calipers. It may be easier to get the calipers back on to the rotor and then install the new pads.

Step 12 – Re-install caliper bracket and calipers

Put the caliper bracket back in place as well as the housing. Wiggle the housing on the rotor, sliding it up and down until the bolt bites. Tighten all the caliper and caliper housing bolts and then torque them to specifications. If you haven’t installed the new brake pads, do so now before you tighten and torque the housing bolts.

Step 13 – Re-install the spindle nut and wheels

You are almost finished. Put the spindle nut back on and use a screwdriver to deform it back into the void part of the drive shaft. Tighten down the spindle nut to at least where the end of the shaft meets the end of the spindle nut. Actual specifications call for about 181 ft.-lbs. of torque.

You will need your helper to step on the brake pedal before tightening. Keep pressing on the brake while you put the tires back on and tighten the lug nuts.
Lower the car off the jack stands and torque down the lug nuts.

General Description:
It is one of the best Juice Packaging Machinery in China.This is a fully-automatic packing machine with Form-Fill-Seal function which is widely used for food, beverage, cosmetics, chemicals, pharmaceuticals packaging. This type of machine is well used in Europe and America. The packing material can be regular laminated film such as, PE/AL/PET; PE/NY/AL/PET; CPP/NY/AL/PET. This type of machine can make stand up pouch and then finish the packing process. The main packager can be integrated with various filling systems, suitable for all kinds of products, such as powder, small granule, liquid, viscous liquid, paste, tablet, candy, solid, stick, large solid and irregular products.

Applications:
It can be used to pack liquid product such as milk ,juice, ketchup ,paste, shampoo,detergent etc. up to 1000ml by changing filling device.

Function:
The machine can automatically finish bag forming, filling, easy tear notch making, print date, finished bag discharged. Reclosable zipper, spout , nitrogen flushing, unique bag shape ,hole and Round corner punching are optional.

Characteristics:
1) easy and fast adjustment of change over, the machine has strength extensibility, could fill two or even more products into one bag by added filling device .

1.Case Erector
Capacity : 8-12 Cartons/min.
1.The case blanks stand vertically in the quick load magazine which has space for more than
2.100 blanks (may be different according to the thickness of the carton).
3.The blank is picked up from the magazine by a device with suction cups and erected
4.To the carton holder. The erected carton is fed by a mobile mechanical movement,
5.The tape glue is applied on the long flap during feeding.
6.All parts coming in contact with the packs are made of stainless or rust protected material.The machine is controlled by a micro computer( also called PLC).

2.Case Packer

Composed of:

- N. 1 Infeed conveyor
– N. 1 Loading station
– N. 1 Guide rail – N. 1 Carton holder

Product to be wrapped: PET-bottle of drinking water
Pack collation: 5*8 4*6 in carton
Speed: 10-12 cartons/min General Specifications

1. The packer are manufactured with solid profiled steel welded constructions. Torsion-free, working reliability and extended life.
2. All parts are painted with a two component epoxy paint.
3. The system has memory sets for save data and easy to use on multiple packages next time.To show the survey the error and point and guides to operation and maintenance.
4. The packer can be altered to different size within 30 minutes by miner adjustments or substitution of change parts, provided that the machine is not manufactured for a single-purpose operation.
5. Reliable and precise case transport. Well-guided case transport is guaranteed by roller conveyors gripping the case at 3 edges ensuring perfect alignment.
6. Overload system : Minimizes possibility of damage to product or machine in the event of a jam or malfunction.
7. Using the touch screen to setup or reset the PLC program.
8. Wide variety of lane dividers, loaders and infeed timing devices..
9. Control power uses the low voltage DC24V to avoid electric leakage.
10. This machine is easy to operate, do not need major technical staff.
11. The action parts of machine have the glib for easy lubrication and maintenance.Even the bearing is on the bottom, has linked a pipe for gather up the lubrication. 3. Case Sealer
1.Automaticlly fold the top panels ,stable and smooth ,beautiful look an save the labour,can be used with the Automatic Packaging Machine Series.The lastest patent tape attaching device,no need the fan to blow the tape to make it smooth ,apply the patent pressing device,ensure the tape tightened avoide the ineffective taping.
2.high precision ,low noise ,longer the life of the belt.
3.It is able to do auto folding for top lid.
4. Adjust the width and the height manually according to the carton size.
5.Imported of components Electric and pneumatic parts.

4. Case Palletizer

1. Introduction

a.The Automatic Palletizer can put different products in a fixed order and stack them on the pallet automatically.

b.Number of product and layers can be set .

c.Easy for the fork moves the full pallet into storehouse.

d.This equipment adopts PLC ,touch screen and intelligent managing which is not only simple and easy to master, but also reducing the labor.managing which is not only simple and easy to master, but also reducing the labor.

BEST REGARDS

Tony
whatsapp/Tel/wechat: +86 18701769069
skype: wangwei6350
email: tony@rutianpack.com
website: https://aotupack.en.alibaba.com
address: No. 689. Yang Pai Road, Fengxian District, Shanghai, China
shanghai Rutian packing machinery